Why won't my e-cigarette charge?

When does your e-cigarette need recharging?

If the battery charge in the device drops to 30%, the LED sensor starts blinking.

The method of signaling depends on the type of vape:

• there are models in which data on the battery charge level appears on the display;
• There are devices that transmit information only using a flashing indicator.

Certain signs allow you to understand that the battery has run down to a critical level:

• the volume of steam produced is greatly reduced (or its production stops completely);
• puffing becomes difficult (the effort when inhaling vapor increases significantly);
• the gadget begins to leak (the evaporation of the smoking solution from the wick slows down because the coil receives a small amount of energy).

Juul is not charging - what should I do?

Why did my JUUL stop charging?

Magnetic USB charging is a critical point of failure for your JUUL—and most people never consider this fact until their first JUUL stops charging. If this little charger doesn't work properly, you won't be able to use the Pod, unless you have a backup charger of course. Unfortunately, most stores that carry Juul don't sell separate chargers, so it's unlikely you'll have it anyway.

What to do if your Jool won't charge

Clear all contacts!

Start by cleaning the charging contacts and the bottom of the JUUL itself. If you carry your e-cigarette in your pocket, it's likely that the recessed charging contacts at the bottom have kicked up dust and dirt. You can use a toothpick to scrape off the residue without worrying about damaging the contacts. Do the same with the charger. If its contacts are dirty, clean them with a cotton swab.

Try a different USB port

The Jule charger is designed to work with the USB port on any computer, but computers don't always behave as they should. Before you assume that your JUUL charging is causing the problem, try the USB port on a different computer. Do not try to charge with a fast charging wall adapter for your cell phone or tablet!

Replacement equipment if possible

It's likely that you've already tried charging your JUUL with a different charger, if you have one. If you haven't tried a different charger yet, now is the time to do so. You should also try charging another Jule battery if you have one. If you can charge your Jule after replacing the battery or charging it, then you have successfully identified the fault that is causing the problem. This doesn't necessarily mean that you need to discard the problematic component, it just means that you know the component that needs troubleshooting. Don't give up until you try all the tips in this article.

Make sure your JUUL battery is dry

You may experience JUUL leaks from time to time. If this happens and you see liquid inside your device's battery, this could have catastrophic consequences. What to do about it? Look at the condition of the battery by first checking under the cartridge. If you haven't already cleaned the top compartment of the Jule, use a cotton swab or paper towel to remove any condensation from underneath the pod. Then, holding the paper towel over the battery, blow it hard from below. Is the paper towel wet? Do you see moisture at the top of the battery? If so, there is moisture in the battery. Continue purging the battery and wiping away the e-liquid until you have removed as much as you can.

Did the Jewel start charging at this point? If not, then try sealing the battery in a plastic bag for a day or two with a cup of dry rice or a packet of silica gel. If your device still won't charge after you take out its battery after a couple of days, it's likely that leaking fluid has ruined the battery.

Why does the electronic cigarette not charge?

If there is a problem with charging your gadget, you should not get rid of it immediately. There are several simple ways to quickly fix the problem.

The device stops charging for the following reasons:

• no contact;
• a short circuit has occurred;
• the service life has expired;
• damage has occurred in the board;
• contacts are clogged;
• The charger or adapter does not work;
• The device was blocked.

Contact lost

The vape fails if the contact connecting the battery and the atomizer falls in. To detect a malfunction, unscrew the battery and inspect the connections of the wires.

Contacts are clogged

In order for the electronic cigarette to work properly, you should periodically examine and clean the contacts. Prevention is carried out once a week.

Short circuit

The gadget stops working after a short circuit. The malfunction occurs when the smoking solution leaks into the battery niche.

The board is damaged

Often the board burns out due to moisture entering the battery socket. The cause of the problem can also be a manufacturing defect.

Expiration date

The battery in an electronic cigarette is designed for a certain number of recharges. A battery that has reached its limit will fail. The battery becomes unusable after 500-800 charges.

Conditions for choosing and using an electronic cigarette battery

A properly selected battery, operated under acceptable conditions, is the key to long-term operation of the entire device. When buying a new battery, you need to make sure that it fits this electronic cigarette; in addition to the obvious match of contacts, fastener type and dimensions, you should take into account several more parameters:

1. Maximum battery discharge current. This parameter shows the maximum current that the battery can discharge without damaging it. The maximum battery current should not be less than the current consumed by the evaporator coil.
2. Capacity. The capacity of the battery determines how long it can work without recharging. With a large battery capacity, the number of charge-discharge cycles is significantly less, which increases the battery life.
3. Correspondence of the current and voltage of the charger to the parameters of the vape battery.

By choosing a battery in accordance with the above rules, you will ensure long-term performance of your electronic cigarette and enjoy its use.

What to do if your e-cigarette battery does not charge

When the electronic cigarette stops charging, perform the following steps:

1. Check the functionality of the charger. Connect the device to a working USB cable.
2. Remove the blocking. The electronic cigarette will start working after pressing the special button 5 times.
3. Charge a dead battery. The device will turn on no earlier than 15 minutes after connecting to the power supply.
4. Check contacts. The gadget is unscrewed; if the contacts have come loose, they are corrected with a needle. Carefully assemble the device.
5. Clean contacts. Wipe the metal plates with a cotton swab moistened with alcohol. Remove the accumulation of dirt with a needle in hard-to-reach areas.
6. Check the expiration date of the battery. The battery, which has served its allotted time, is replaced with a new element.

Cigarette refuses to charge

The main task of the battery in an electronic cigarette is to supply electricity to the vaporizer so that the liquid heats up and the process of generating vapor begins.

When buying a battery for a device, you need to pay attention to its compatibility with this cigarette model. Batteries differ mainly in capacity and chemical properties.

When using an electronic device for the first time, you should completely discharge the device, and when charging for the first time, you do not need to interrupt the process, although this time it may take quite a long time. Otherwise, the device's battery power may be degraded.

All subsequent charges will take place faster, their duration depends on the battery capacity: on average from 1 to 5 hours. With proper use, the charge of the device should not drop to zero, but the charger should not be turned on too often, as this will negatively affect duration of battery wear.

It is best to have a spare battery in case the main one fails at the wrong time. Why the battery does not charge Now it is worth considering the main reasons why an electronic cigarette does not charge.

First you need to wait 15 minutes after connecting the device to power.

It happens that a completely discharged cigarette battery does not start charging for some time, and then everything goes fine. If, after all, the electronic cigarette does not start charging, you need to pay attention to the condition of the charger

If the cord or plug is damaged, electricity simply will not be able to flow into the device. Perhaps the adapter is to blame, this is checked like this: the adapter plugged into the network is simply connected to another battery.

The battery may be damaged. This could happen due to liquid getting inside, for example. For the same reason, the board could be damaged. Sometimes a short circuit occurs due to moisture, and the board could burn out, in which case you cannot do without specialists.

To do this, you need to insert a needle between the battery and the central contact and remove it. After this procedure, the battery is carefully screwed into place. When twisting the thread, you do not need to tighten it too much, but at the same time you need to make sure that it fits quite tightly.

This is an important point, since the device may stop charging in both the first and second cases. When disassembling the design, it sometimes turns out that the contact is broken, so the device’s battery does not work.

Clogged dirt from hard-to-reach places can be removed with a needle. The standard battery capacity is designed for approximately 500 charges. If you've been using your device for a long time, your battery may need to be replaced.

When the charging indicator does not turn on and the charging of a new electronic cigarette does not occur, it is best to consult a service center. If there is a warranty on the electronic device, faulty parts of the device will be replaced with new ones.

If the user is sure that the battery of the smoking device is dead, but the device stubbornly does not want to charge, it is worth trying to wait 15-20 minutes. Perhaps the cigarette will “come to its senses” and begin to recharge itself. This often happens when the battery is completely discharged.

But, if after some time the electronic gadget refuses to charge, the culprit should be looked for elsewhere. If the electronic cigarette does not charge, what to do - find out the reason. There may be several culprits.

To understand the nature of the malfunction, you need to try connecting the gadget to a new, working charger. You should first test the charger on another cigarette.

Moisture can get inside the device or mechanical damage to the board (shock, strong shaking) can occur. The charge controller may also have some kind of manufacturing defect. This can lead to damage to the board and failure of the battery to be recharged. Then the only thing you have to do is replace the board with a working one.

Some smoking devices have a battery lock feature. This ability, provided by the breeder, helps to transport the mod safely. If you block the battery, you can avoid accidentally turning on the vape during transportation.

If the gadget does not want to work, check if the battery is simply in a blocked state. To disable the lock mode, you should press the power button a number of times in a row (3-6, it depends on the mod model).

Why does the device discharge quickly?

Instantaneous discharge of an electronic cigarette is not uncommon.
If this problem occurs, you first need to make sure that the battery is not blocked. If after pressing the button 5 times, the gadget does not start working, then it needs to be connected to the power supply. Rapid discharge of an electronic cigarette is caused by:

1. Frequent use of the gadget.
2. Battery power. The discharge rate is affected by the battery capacity. When purchasing a vape, you need to check its capabilities. For those who smoke a little and for a short time during a session, electronic cigarettes with a capacity of 180 mAh are suitable. For intensive use, purchase devices with a 360 mAh battery. Low-power gadgets are thin and elegant. Women prefer to use them.
3. Violation of operation. Incorrect use of electronic cigarettes immediately after purchase leads to rapid battery discharge. Device malfunctions occur if the user recharges the gadget without waiting for the battery to be completely discharged. The device should be connected to the power supply when the battery is completely drained. This procedure must be performed 3 times. In this case, the gadget is removed from charging after a signal sounds indicating the completion of the process.
4. Environmental conditions. The batteries of electronic cigarettes are instantly discharged at low temperatures. The devices are not recommended for frequent use in the cold. When used in such conditions, battery life will be significantly reduced.
5. Smoking process. When drawing in vapor, simultaneously press the button and puff. This is a prerequisite to extend the use of an electronic cigarette. Advanced owners are advised to release the button 2-3 seconds before completing the tightening. At this point, a sufficient volume of vapor has been generated for inhalation. The smoking process is comfortable, and the battery power is consumed economically.

The operation of the electronic cigarette will not be disrupted, the parts of the gadget will not be damaged if you use the original device (included with the vape) for recharging. The device lasts a long time if the owner charges it correctly, keeps the battery clean, and does not allow smoking liquid to leak into the battery socket.

Why won't my IQOS case charge?

The problem with recharging the IQOS case may not lie in a breakdown of the battery itself. Most often the reason is:

• deep discharge. You need to connect the case to the adapter and wait about 20 minutes, the indicator should start flashing;
• Using unsuitable chargers. It is worth using only original components;
• problems with wires and contacts. Clogged plugs often cause problems;
• mismatch between the parameters of the voltage used. Computer USB connectors may not be suitable for charging IQOS;
• system failure. This sometimes happens due to being plugged in for a long time. In this case, you need to restart the device.

Some users are careless when using IQOS. Falls from a height, getting wet or similar physical impacts may cause the device to not charge. Any technology must be treated with care. But this, unfortunately, does not eliminate the risk of spontaneous failure: for example, Apple headphones exploded right in the ear of their owner.

What does the flashing red light mean?

IQOS is equipped with a number of indicators that help identify malfunctions. The device will independently analyze the system and issue a corresponding light signal.

The red LED indicates low battery. It is worth connecting the case to the adapter, if the indication stops, then everything is in order. If IQOS continues to flash red during charging, you should look for problems in the wires, contacts or the device itself.

What does the blinking white light mean?

The white light on the case does not mean anything bad. It can inform you either about the completion of the system reboot process, or about the charging of the device placed in the case.

The manufacturer does not recommend charging the holder simultaneously with the IQOS case. Such an action often causes a system failure.

More negative information comes from the complete lack of indication when manipulating the case. This may indicate mechanical failure or deep battery discharge.

Rules for charging an electronic cigarette

It is very important for novice users of electronic cigarettes to study the instructions for the device, since only with proper care will it work for a long time without losing its functions. The most important thing for a beginner is to find out what signals the device signals in this or that case, and how it should be charged. We will look at all possible ways to charge the device, as well as possible problems associated with this process.

When does your e-cigarette need recharging?

Most often, when the battery charge drops to 30%, the electronic cigarette warns the user about this by flashing the LED. Methods of informing about low battery depend on the device model. For example, in the Ego-T and Evod electronic cigarette models, the indicator will flash 10 times when the battery is low.

In mods equipped with a display, this information can be understood from the data that is displayed on a small screen. It shows how much battery charge remains in percentage.

Also, if the battery is dead, some gadgets may present the following symptoms:

• the amount of steam produced decreases or does not form at all;
• when tightening, more effort is required than usual;
• the device leaks because the liquid does not have time to evaporate from the wick due to insufficient energy supply to the coil.

Battery charging methods

An electronic cigarette is charged in three standard ways, not counting the methods invented by folk craftsmen.

Via 510 connector

This method is used in eGo electronic cigarettes. To connect the gadget to the charger, you will need to disconnect the clearomizer. The advantage of this connection is that when the device is operating, the contacts are hidden under the evaporator and protected from accidental ingress of moisture. The main disadvantage of connecting via the 510 connector is the special charger. If there is no charger or it is out of order, you will have to buy a new one or make a homemade one.

From the network

You can also charge an electronic cigarette from the network if you use a simple AC adapter with the appropriate voltage and output current to connect the USB cable. Also, some battery packs (mods) use AA batteries, which can only be charged using a charger for removable batteries.

From USB

All vapes of a class higher than the entry-level eGo are connected to charging via USB (micro). In this way, you can charge, for example, iJust S and iJust 2 vapes. Among the advantages of charging via micro USB are the following:

• no need to disconnect the evaporator when connecting to the power supply;
• versatility - you can use a charger from other gadgets;
• the presence of a Pass-through function, which allows the vaper to vape while recharging the battery.

Battery charging time

The time it takes for the battery to reach full charge directly depends on the capacity of the battery and the current that the charger can provide at the output . If you want to use a power supply from another device or its homemade analogue, then calculating the charging time is very simple. For this there is a formula T = 1.4 C/I, where:

• T is the time in hours during which the battery needs to be charged;
• 1.4 – coefficient, calculated from the average charging efficiency and used for correction;
• C – battery capacity in mAh (milliamps per hour), which can be found in the instructions for the gadget or mod;
• I – charger current.

To find out the latest indicator, look at the markings on the charger. Opposite the word “output” a value will be written, for example, 500 mA.

For example, your vape has a 900 mAh battery, and the charger is capable of delivering 500 mA. If we substitute this data into the formula, we get: T= 1.4 * 900 / 500 = 2.52. Thus, it will take about 3 hours to charge a 900 mAh battery.

All these calculations will be useful to you if you are using a vape, the design of which does not provide for indication and automatic shutdown of the charging process when the battery reaches full capacity. Basically, when you put your e-cigarette on charge, the light on the power button will light up. Depending on the model of the gadget, it may emit a red glow during the charging process, and a green glow after it is complete. Also, the indicator can light up in one color, and after the battery has been charged, it can simply turn off.

If the battery is new

When buying an electronic cigarette, you should take into account the fact that its battery is in a slightly charged state, sufficient to test the vape for functionality. Therefore, in order to properly charge a new battery, it must be completely discharged. Use the device until you see that the steam has decreased or disappeared altogether, and the light indication confirms that the battery is completely discharged. After that, fully charge it. Perform 3 cycles of full discharge and full charge. This procedure will help “swing” the battery, which will subsequently affect its capacity.

Some vapers recommend charging a new (discharged) battery for at least 8 hours, and then using the device as usual, charging it for an average of 3-4 hours (depending on the battery capacity).

How to charge a gadget without a charger

Sometimes a situation arises when the power supply of your electronic cigarette, for example, Ego-T or evod x9 - x6, fails, or you ordered an electronic cigarette via the Internet, and the gadget arrived without charging. In this case, you can quickly make a temporary charger. To do this, you will need a regular USB cable that connects to a computer or laptop, after a little modification.

1. It is necessary to cut the end of the cable and strip the top insulation. Next, find the red and black wires, then strip their ends (you can solder them). Remember, the red wire is “+” and the black wire is “-”.
2. Take a small piece of paper and make something out of it in the form of a plug, into the center of which insert the positive contact so that it protrudes about 3 mm from the bottom. To prevent the cork from unwinding, wrap it on top with electrical tape.
3. Disconnect the clearomizer from the battery. If you look at the charging connection location, you can see the central contact. It is to this that the “+” should be connected, and the “-” to the body.
4. Insert the plug into the hole in the battery pack so that the end of the wire (red) touches the center contact of the battery. The negative wire can be secured to the body using an alligator clip or using a regular clothespin.
5. Connect the cable to the USB port of your computer. If the process of energy accumulation has begun, it means you did everything right.

But first, look at the instructions for your vape. Namely, what voltage and current is the cigarette battery designed for. If the instructions say that the input voltage is 3.7 V, then you cannot charge the battery from the USB port, since it gives an output of 5 V and 500 mA. In this case, you can use an old phone charger with an output voltage of 3.7 V and a current of no more than 1 A.

But still better than a homemade one, there will be an adapter bought in China at a price of only 56 rubles.

The adapter connects to the USB port of a PC or laptop or to a network adapter whose parameters are 5.0V - 500mAh.

If you purchase an AC adapter, the vape can be charged from an outlet.

How to charge a disposable e-cigarette

To charge a disposable e-cigarette, you first need to take it apart.

1. Using a paper clip or a pen refill, remove the plastic plug that acts as a mouthpiece. Under it you will see a wick that will need to be soaked with liquid.

2. Next, remove the LED cover located on the opposite side of the device. Sometimes the cover can be soldered to the LED and be one piece with it. If this is so, then what to do will be discussed below.

3. Using a thin rod, push the contents of the e-cigarette out of the housing from the LED side. If the bulb is soldered, push out the “insides” of the gadget from the wick side.

4. You will see a battery with contacts soldered to it. Usually there is a “+” on the side of the light bulb, and a “-” near the wick. Take the phone charger and connect the wires, observing the polarity (red is positive, black is negative).

5. To charge the battery, plug in the power supply for approximately 30 minutes. This time will be enough. Do not leave the process unattended - periodically check the battery temperature. If it becomes hot, turn off the charger as overheating may cause the battery casing to explode.

After recharging, reassemble the device in reverse order and place a few drops of e-juice on the wick. Now you can use your disposable e-cigarette again. Although no one forbids doing such a procedure with a gadget as many times as the battery life lasts.

Why does the electronic cigarette not charge?

If you connect your device to the charger and notice that it is not charging, wait about 15 minutes. and check again. There are cases when, after a battery is completely discharged, it takes some time for it to begin to gain energy, after which its accumulation proceeds as usual.

Make sure that the gadget's battery is not blocked from accidental pressing. To do this, press the power button 3 to 5 times in a row (depending on the vape model). If the command has been accepted, the button should blink and will remain lit the next time it is pressed.

Also, the reason that the battery does not charge may be a faulty power supply, the cable itself, or the charger plug.

Poor contact at the charging connection cannot be ruled out. The contacts may become clogged or unsoldered. If they become dirty, wipe them with a cotton pad soaked in alcohol. If the contacts are unsoldered, you will have to use a soldering iron to repair the damage.

Also, the battery can fail if liquid gets on its contacts, resulting in a short circuit. Sometimes the electronic board also burns out. In this case, you will need the help of a specialist from the service center. If the electronics have survived, then you can try to remove any remaining moisture from the battery and turn it on for recharging again.

If the gadget discharges quickly

The quick discharge of the gadget is puzzling, especially for novice vapers. The reasons for this trouble may be different.

1. Remember that the battery is not eternal - it tends to exhaust its life. On average, the battery is designed for 500 charge-discharge cycles. Therefore, after using your vape for a long time, you may notice that the battery drains quickly. The problem is solved by replacing the battery.
2. You should also match the battery capacity to your vaping needs. This relationship can be clearly seen in the following figure.

3. Soaring in the cold drains the gadget very quickly. 50-60 puffs with a battery capacity of 1100 mAh are enough for it to completely lose all energy.
4. Sometimes the blinking indicator is mistaken for a signal indicating a dead battery. This often happens if the steamer takes long or sharp puffs. And since all batteries have protection against overheating, the so-called “cut-off”, after 6 seconds (on average it takes 5 seconds to tighten), it is triggered and the LED blinks. To determine whether it is indeed a “cut-off”, disconnect the atomizer from the battery and press the button again. If the blinking repeats, the battery is low.
5. Also, the reason for the rapid discharge of the battery may be the high resistance of the coil in the clearomizer. Try installing a different miser with less resistance.
6. If the mod is set to high power to produce a huge amount of steam, the battery will drain very quickly. It is necessary to avoid high powers, because, in addition to the rapid loss of battery energy, you will get a burning taste.

Other reasons for rapid battery discharge may be hidden in the electronic board. In this case, the gadget will have to be taken to a service center for inspection.

Sources: https://tehnika.expert/cifrovaya/elektronnaya-sigareta/kak-zaryadit.html https://broshu-kurit.ru/kakoj-atomajzer-vybrat.php