Reasons why the Indesit washing machine does not turn on

Electrical faults

In some cases, the Indesit washing machine is fine. The reason is a network fault. The repair consists of checking the outlet. To do this, simply plug a known-good device into it.

Sometimes the washing machine does not turn on or work due to a faulty cable. In both cases, you must be careful: turn off the electricity and only then begin repairs. It is advisable to entrust this matter to a professional electrician.

Socket repair

Indesit wisl 103 malfunctions and their solutions

• The washing machine does not turn on. Check the outlet. To do this, it is enough to include a known working electrical appliance in it. And be sure to make sure you pressed the “on/off” button.
• The selected wash cycle does not start. There are several possible reasons: the door is not closed or poorly closed, the “on/off” or start button is not pressed, there is no water supply, or the “delay start” function is programmed.
• It’s easy to deal with blockages and small leaks yourself.
  No water is poured into the machine. Possible reasons: the inlet hose is not connected or pinched, the supply is turned off by the tap or there is no water in the water supply system, the “start” button is not pressed. The washing cycle may not start even if the water pressure in the water supply is low.
• Water is constantly drained and refilled. Check that the drainage system is installed correctly. The drain hose must be installed no lower than 65 and no higher than 100 cm from the floor, and its end must be above the surface of the flowing water. Owners of washing machines living on the upper floors of high-rise buildings must install a special anti-siphon valve when installing them on the drain system.
• The machine does not drain water and does not spin clothes. The easy ironing function and some washing modes are programmed to operate without a drain/spin cycle. If the selected mode provides for such a cycle, but it does not start, check the drain hose for kinks and blockages.

Quite often, the owners of a washing machine are responsible for the occurrence of an emergency situation not because of its breakdown, but because of their own incorrect action:

• Excessive foaming. The reason may be either an incorrectly selected powder that is not suitable for this type of machine, or an excessive dosage of detergent.
• Leaks on the floor occur when the drain and inlet hoses are connected incorrectly, or due to blockages in the detergent dispenser.

The above problems can be avoided if you install and operate the washing machine in accordance with the included instructions, and in case of possible blockages or small leaks, the situation can be easily corrected on your own. However, there are malfunctions in which a call to the service center cannot be avoided.

Interference filter and network cable

The Indesit WISLI washing machine still won't turn on? Next you should look at the power cord of the Indesit washing machine and the plug, as well as the interference filter.

You will have to remove the network connector and the filter at the same time, since they are connected.

To do this you need:

1. Disconnect everything unnecessary from communications.
2. Turn the Indesit washing machine.
3. Remove the screws and then the cover.
4. At the top left is the capacitor. It needs to be removed from the mount.
5. At the base of the case there is also a mount that secures the cable. It needs to be disconnected.
6. After the previous manipulations, the network connector with the filter can be easily pulled out.

Interference filter in a washing machine

Next, you should disconnect the filter and check the power cord. This is done by ringing with a multimeter. If a breakdown is found, the entire wire must be replaced. It is not recommended to repair the old one or replace the cores in it.

Interference filter

After this, the interference filter rings. The probes are installed on the legs of its capacitor. If everything is normal, the resistance is additionally checked. If the value is “0” or “1”, the cause is the capacitor and must be replaced.

Troubleshooting

Some series of Indesit Wisl washing machines have a test mode, which can be used to determine the type of problem. They are equipped with a display where the error code is displayed.

On models without an electronic display, a specific combination of LEDs on the front panel will light up when a problem occurs.

To identify errors, you need to pay attention only to the top row of LEDs located above the four additional program buttons. By checking the table you can find out the error code and the cause of the failure

Control module

If after this the indicators do not light up, then the reason is different. Next you should try checking the control module of the Indesit WISLI washing machine. These are microcircuits, the “brains” of the device. You need to change something here only with some experience behind you. A video will help with this work.

Washing machine control module

By the way, the causes of other common Indesit malfunctions also lie in the control boards:

• if all the lights on the panel blink;
• if there are problems with spinning, etc.

When the capacitors on the microcircuit fail, the indicators usually begin to blink simultaneously. Replacing capacitors is the easiest way, but you will need good soldering iron skills and the right model. After replacement, as a rule, the light bulbs stop blinking.

If there are problems with spinning, they also look at the electronic module. This is not an easy task and requires knowledge and preparation. That is why, if the spin cycle does not work correctly, it is advisable to give the board to a specialist.

Device is not working? Why does the Indesit washing machine blink and not turn on? You need to look at the varistor - part of the microcircuit, a resistor necessary to protect the board from voltage surges.

Varistors microcircuits

Replacing it is quite simple with your own hands:

1. Remove the powder container. Underneath there are two screws that need to be unscrewed.
2. Remove the control panel.
3. Disassemble the unit and disconnect the board.
4. Find the varistors and check their resistance using a multimeter. Often the part turns black or falls out completely.
5. The burnt varistor is soldered off. It is replaced by another one with similar characteristics. The device should start working.

When using a soldering iron, you need to be careful not to damage the traces and other elements of the printed circuit board. If this happens, most likely, you will no longer be able to do without the help of a specialist.

You should also keep in mind:

1. Varistors are not the only possible malfunction that leads to the Indesit WISLI washing machine not turning on. This is just one of the simple and common ones.
2. In case of inept repair, the microcircuit can be permanently damaged beyond repair. Its cost is approximately 20% of the price of the entire Indesit washing machine.
3. Service centers usually do not repair the board, but install a new one. It’s easier, faster, and most importantly – more profitable. Private craftsmen often undertake repairs. Their repairs will be cheaper, but you should pay attention to their experience and qualifications.

Problem with water supply to washing unit

There may be several similar problems, and they are associated with different parts of the washing machine.

First of all, you should make sure that the water supply is not temporarily limited or the pressure in the network is not reduced.

When drawing and draining water into the machine, you need the system to understand when the liquid reaches the desired level. The water pressure sensor is responsible for this. It is called a pressure switch. It measures the pressure in an empty and full tank. If the sensor simultaneously receives a signal that the tank is empty and full, then water will not be supplied. This occurs due to sticking of the sensor contacts. In this situation, replacing the sensor will help.

Only a specialist can determine the cause of such a malfunction, since the flow of water may be limited due to other components. For example, a control unit or electrical wiring.

The intake valve may also be faulty. It is responsible for filling the water to the required level and then shuts off the water supply. The housewife may notice this problem if the tank is not filled with water during the time allotted by the program. And also when the machine is not working, the tank is filled. On models with a display, error F10 or H20 will appear.

To correct the problem, you can try to clear the pipes and hoses from blockages; in extreme cases, you will have to replace the valve.

The mesh on the inlet valve can be kept in a solution of vinegar or citric acid to remove scale from hard water.

Start button

Another reason may be that the device's start button is faulty. As a result, it does not turn on. Often such a breakdown occurs in older models of the Indesit washing machine, released about 15 years ago. Due to their features, if the button fails, everything else does not work.

The following actions are performed:

• the control module is removed according to the scheme discussed above;
• the resistance on the button is determined, and it must be on;
• If this is the case, a new one is installed.

If after all the above checks the machine still does not turn on, the reason is not common or something was done incorrectly. Then it is better to call a specialist.

Common faults

A reliable and useful assistant in the home is a washing machine. And its breakdown is a big problem. You can buy the required washing machine at a hardware store, but none of the models is protected from breakdown.

Household appliances can become damaged after 5-6 years of operation. This is a common phenomenon, because the technique is intensively used, and it has its weak points.

The most common washing machine faults:

• the whole device flashes;
• weak spin of laundry;
• Difficulties with the control module.

Having identified the problem, repair the Indesit washing machine yourself.

• do not spin the drum;
• grinding, humming and other sounds during spinning;
• dilemma with heating, water supply and drainage;
• the appliance leaks when draining;
• the device does not start;
• The door lock does not work;
• Spin does not work;
• unpleasant smell from the car.

Causes of level sensor failures

Sometimes the level sensors on washing machines break down. These elements fail due to malfunctions of the module. The breakdown may also be caused by network overload. Level sensors cannot be repaired, but they can be replaced. For this purpose, it is necessary to ensure that the elements are broken. To do this, remove the lid from the washing machine and inspect the drum. The level sensors are located under the plate and are connected to it through contacts. If the tester shows a zero value, then the device is broken. It needs to be changed.

Equipment from any manufacturer breaks down over time, and Indesit is no exception. Sometimes, having decided to do the laundry, the user may find that the Indesit washing machine does not turn on. There can be many reasons for this, ranging from a power outage to a broken control board.