Like any equipment, the Indesit washing machine can sometimes malfunction. One of these situations is the lack of drainage and freezing of the washing process.
In some cases, you can cope with the failure yourself, in others, you cannot do without the help of a specialist.
What to do if the Indesit washing machine does not drain water, what are the reasons for the breakdown, what are the ways to solve the problem, we will tell you in the article.
Diagnosis of Indesit washing machine errors
It should be borne in mind that the absence of drainage during operation of the washing machine does not always indicate a serious breakdown. This may be an easily fixable failure , which will not be difficult to cope with.
When stopping the cycle without draining, it is necessary to sequentially analyze the situation and study the condition of the nodes involved in the water discharge process. You can start with the simplest and, according to statistics, more frequent problems, gradually moving on to more complex ones.
Diagnostics must begin by checking which mode was selected on the Indesit washing machine, and whether an error code is displayed on the display. This is necessary to ensure that the no-drain mode has been configured. Then the remaining water in the tank is the normal state of the washing machine.
Some wash programs include a water stop. If the user selects this washing mode, then stopping is not a failure, this is a normal situation.
Most often, stopping without draining occurs in the following modes:
- wool;
- silk;
- delicate fabrics.
If a fault code appears on the display, it should be analyzed as it indicates the cause of the problem. Based on this information, you should check the functionality of the nodes:
Codes F05 and F11 may indicate a pump malfunction.- A problem with the control module is often indicated by codes F09 or F18.
- A failure of the pressure switch can be signaled by code F04.
- Problems with the electrical system and drain pump contacts are indicated by code F05 and code F11.
- Drain filter clogged.
- Installation and connection of an Indesit washing machine with irregularities (kinked drain hose, incorrect installation, etc.).
- Clogged sewer system.
In addition to the listed node failures, a one-time failure in the operation of the equipment is possible, which will not recur after a reboot and is caused by a random combination of circumstances.
We are looking for the reason ourselves
- Check if the mode is selected correctly? Almost all machines have a washing mode with a stop with water, that is, without spinning. Typically, this mode is used for delicate fabrics or wool: gentle rinsing without spinning does not deform things - they do not stretch or wrinkle. If the water stop mode is selected, you must press the “Start/Pause/Cancel” button and start the water drain program.
- Check if the drain hose is ok? It may be “kinked” or compressed so that water cannot physically pass through the bend.
- Check if there is a blockage in the drain or siphon (if the drain hose is connected to the siphon)? To do this, you need to disconnect the hose and hang it in the bathroom or sink, and then turn on any mode. If water flows freely from the hose, it means there is a blockage in the sewer system. It needs to be cleaned, either yourself or by calling a plumber.
If you made the right choice of program and all “external communications” are normal, then we are talking about a breakdown in the machine itself. In this case, we recommend turning off the washing machine from the network, removing the laundry from the tank and draining the water using the drain filter (it is located in a small hatch at the bottom of the unit).
Do not forget to place a basin or bucket so that the water from the machine does not spill on the floor!
What to do if the drain doesn't work?
When the washing machine stops operating and there is water left in the drum, it is necessary to analyze the situation and determine the cause. You should start with the selected washing program.
Delicate mode
If, when starting the wash, a mode was selected that does not provide water discharge, then you must :
- turn on the washing machine (if it is turned off);
- in setting the modes, select only “drain” or “spin”, without the washing itself, you also do not need to add detergent;
- After the end of the program, things can be taken out of the drum without problems.
The solution to the problem is to set the drain mode.
Drain filter clogged
If the drain filter has not been cleaned for a long time, this procedure should be carried out immediately. Access to the filter is from the front side below. Before carrying out work, the machine should be de-energized.
The solution to the problem is cleaning the filter. Cleaning procedure:
- Open the panel.
- Turn right and pull the filter towards you.
- Clean and rinse the filter.
- Return the part to its original place.
- Install the cover panel.
When cleaning the filter, water is drained, so it is necessary to place rags in advance and prepare a low container for draining the liquid.
The drain in the house is clogged
To determine whether the problem is caused by a general clog in the drain, you need to observe how the water flows from the sink and bathtub. Additionally, you should (if possible) conduct the following test:
- disconnect the washing machine drain hose from the sewer connection;
- throw the free end of the hose into the bathtub, sink or toilet;
- run only the “drain” mode;
- If water flows, then the problem is not a breakdown of the washing machine, but a clogged sewer.
The solution to the problem is to clean the drain yourself or call a plumber. Once the blockage is removed, the washing machine can be used as usual.
Incorrect installation
For successful operation, the Indesit washing machine must be correctly connected to the communications. For high-quality drainage, it is important that the hose through which water is discharged is raised above the level of the tank, in accordance with the installation rules, but is positioned freely.
It is important that there is no bend and that it is not deformed or pinched, for example, by tightly pushed furniture. The solution to the problem is the correct free position of the hose .
Random program crash
In rare cases, the Indesit washing machine may freeze for no apparent reason.
The solution to the problem is reboot . To do this, the machine must be turned off and turned on again after 20 minutes. After this, select the “drain” mode.
If the outflow of water began, then the cause was an accidental failure. Otherwise, you need to continue troubleshooting.
The cause of unstable operation of household appliances may be voltage surges. In this case, the Indesit connection must be made through a voltage stabilizer.
Drain pump failure
Malfunction of the drain pump is most often associated with the entry of foreign objects into it - coins, torn buttons, etc. If a breakdown occurs, the part requires replacement .
How to change the pump in the Indesit washing machine is shown in the video:
Drain system clogged
When the washing machine enters the draining stage, the pump starts working, the pump pumps water, but the liquid does not drain. In this case, it is likely that debris in the drainage system is obstructing the flow of water.
The following may be clogged:
- drain hose;
- pump, etc.
After identifying the blockage area, cleaning is carried out. The solution to the problem is cleaning the pipes and hose.
Control module failure
If the Indesit washing machine does not drain water or is extremely unstable, draining water not every time, then there is a possibility that the reason lies in burnt-out elements of the control board.
In order to repair the module, professional diagnostics are required , the results of which may require:
- solder the tracks;
- solder the contacts;
- replace burnt out elements;
- reflash the module.
If the board is seriously damaged, a complete replacement of the assembly may be necessary. It is better for such work to be done by specialists who have the skills to perform such work. The solution to the problem is to call a specialist.
What to do if your Siemens washing machine does not drain water?
Rate this article: (2)
A Siemens washing machine does not drain water - this is one of the most common faults. Causes:
- clogged drain pump filter;
- clogged pipe leading from the tank to the pump;
- a large foreign object enters the pump impeller and jams it, after which the pump cannot rotate;
- clogged drain hose;
- clogged siphon or sewer;
- The drain pump is faulty.
Repair:
Disconnect from the network. Disconnect your Siemens washing machine from the power supply!
Pump filter. Check the pump filter for blockages. It is located on the front wall of the Siemens washing machine, below, under the small hatch, on the right or left. The washing machine does not drain water if the filter is clogged. You need to unscrew it and clean it.
Checking the pump filter
Before unscrewing the filter, we tilt the machine back and place a container under it to drain the water, unscrew it carefully so that we have time to screw it back when our container is full. Pump impeller. Check the pump impeller. It is located behind the filter. You need to shine a flashlight into the hole where the filter was unscrewed from and check the impeller itself and around it. Even the entry of a small object (coin, toothpick, hairpin, etc.) can cause the pump to malfunction and the water will not be drained. If you find a foreign object, remove it with your hands or using tweezers. Clean the drain pipe. If, after removing the filter, the remaining water does not drain from the tank, this means that the pipe connecting the tank to the pump is clogged. Then, for convenience, you need to disconnect the pump from the body of the washing machine, or rather not the pump itself, but the entire drain assembly or pump chamber. This is a plastic part that allows you to connect the pump, drain pipe and drain hose together, as well as secure this entire assembly to the body of the washing machine. The pump chamber is secured with screws, after removing which it is easy to disconnect it from the body and it will be easier to get to the pipe. Cleaning the drain system You need to act carefully. Disconnect the end of the pipe that is attached to the pump chamber with a powerful clamp and gradually clear the blockage by cleaning the corrugated rubber pipe and gradually draining the water from the tank into the prepared container. Then reconnect the pipe to the pump chamber, exactly the same as it was at the beginning, without changing anything. If, after removing the filter, all the water flows out of the machine, then the drain pipe still needs to be checked for blockages by probing it along its entire length, and if foreign objects are found in it, carry out the cleaning procedure. Checking the serviceability of the pump. After completing the previous steps, you need to check the serviceability of the drain pump. To do this, connect the Siemens washing machine to the power supply and select the “drain” program (if there is none, then “spin”). In this mode, the pump should begin to rotate, which can be observed in the filter hole. You need to shine a flashlight there and understand whether the pump impeller is rotating or not. If it does not rotate, the pump must be replaced. Replacing the drain pump The first steps to replacing the pump are similar to clearing the blockage from the pipe connecting the tank to the pump, only the pipe itself does not need to be disconnected from the pump chamber. After the machine is tilted back and the pumping chamber is disconnected from its body, it is necessary to disconnect the pump itself from the power supply wires and from the pumping chamber itself. Basically, modern washing machines are equipped with drain pumps of several of the most common types that are usually on sale. One more subtlety. A situation may arise where the water does not drain, but everything is fine. You removed the filter, checked the pipe and drain hose, but there are no blockages, and you can see that the pump turns when you select the “drain” program. There are two options - either the drain hose is clogged and the hose needs to be cleaned, or the pump has exhausted its service life and only runs dry. That is, it can turn without water, but with water it jams, it does not have enough power. This pump must also be replaced. Check after repair. After troubleshooting and complete assembly, you must first visually check all connections affected by the repair and electrical wires supplying current to the pump. Then check the operation of the washing machine in all modes. If everything is in order, unplug the washing machine again, tilt it back and, using a flashlight, check all connections for tightness and leaks. If traces of leaks are visible on any connection, then you need to disconnect and reconnect it again more carefully, and then check everything again. Nothing helped you? Perhaps the problem lies much deeper. A qualified Siemens washing machine repair specialist can help you. Leave a request to call a specialist on the website and receive a 20% discount on repairs.
Call a master: where and how much?
Not in all cases you can fix the problem and get the washing machine working on your own. If you can’t solve the problem on your own, you need to contact a company that repairs washing machines.
You can search for such a company on the Internet by indicating the name of your city. The companies' website contains contact information, a list of work performed and a price list.
Prices from companies vary even within the same city.
Approximate prices:
- Pump replacement – from RUB 1,600.
- Removing blockages in the drain system of the machine - from 1,100 rubles.
- Diagnostics and repair of the control module – from 2,000 rubles.
- Repair or replacement of the pressure switch – from 1,600 rubles.
- Cable replacement, electrical diagnostics – from RUB 1,500. etc.
A serious company that maintains its reputation in the market has a good reputation. You can find reviews on the Internet by company name.
After finishing the work, the master conducts a trial run of the work . If the operation of the washing machine is restored, a warranty is issued for the repair performed.
It is recommended that if your washing machine breaks down, you seek help from specialized companies and do not trust the technician to random technicians, who may turn out to be scammers.
The requirement for an advance payment, the lack of information about the company on the Internet or, conversely, the presence of a large number of negative reviews should be alarming.
A lot of important and useful information about repairing Indesit washing machines is presented in this section.
Reasons for water stagnation in the washing machine
- The filter or pipe in the Siemens washing machine is clogged. In these cases, the water will drain for a long time or not completely. The filter is located in front of the drain pump and traps lint, threads and small debris. If it is not cleaned for a long time, the blockage will interfere with the flow of water. The filter needs to be unscrewed, washed and put back in place. If the problem is in the pipe, then you will need the help of a specialist to open the machine body.
- The pump burned out. The pump rotates at high speed and pushes water into the drain. Damage to the pump is indicated by humming and cracking noises when attempting to drain water. You can shine a light into the drain filter hole and see if the impeller is spinning. If there is no rotation, then a new pump will need to be installed.
- Damage to the control module or water sensor. If the pump does not work and the water does not drain, the electronic control board (programmer) may be damaged. The signal to drain the water does not arrive and does not start the pump, which may be working properly. Sometimes it is not the board that is damaged, but the water level sensor (pressure switch). The control module of the Siemens washing machine does not receive a signal to drain and does not start this function.
