The Samsung automatic washing machine has established itself as a reliable assistant in household chores, however, in some situations, household appliances may malfunction, displaying the error message “le” on the display.
This code indicates that there is a problem that needs to be sorted out. You can fix the cause of the problem either yourself or by calling a specialist.
What is it and what does it mean?
The Samsung washing machine is equipped with a microcomputer that controls all stages of washing. When unexpected processes occur, a certain symbol begins to flash on the screen.
Code le means that the problem is related to the low water level in the drum during the automated washing process.
This could be either a leak or self-draining. The sensor is triggered if, within a few minutes, it detects a decrease in the water level in the tank of the machine four times in a row.
Often, simultaneously with the display blinking, a puddle of water is detected on the floor next to the machine. The time at which the defect occurs may vary.
It often occurs:
- a few seconds after starting the wash;
- almost immediately after filling the tank with water;
- during the washing or rinsing process.
The problem associated with water leakage can be indicated on the display not only in the form of the designation le, but also other codes: e9, lc, le1.
Differences in error encryption are associated with the design features of Samsung machines and the year of their manufacture. Thus, washing units manufactured before 2007 are programmed with the designation e9. More modern models have the letter code le.
If the washing machine is not equipped with a display, then this error can also be easily identified . If water is drained unplanned by the program, the unit signals by flashing indicators.
If an error occurs, two icons glow steadily red: “Bio 60°C” and “cold water”. All washing mode indicators flash at the same time.
Types of LE error codes for Samsung washing machines
The LE fault code on a Samsung washing machine may have the following variations:
- Failure of the water leakage sensor;
- There is a water leak in the machine. As a rule, such an error occurs when the tank and front panel are incorrectly or unreliably fixed;
- Incorrect installation of the spout diaphragm;
- Leakage of water with foam due to the abundance of cleaning agent;
- Water leaks during spin cycle. May occur due to uncoupling of the air hose;
- Water leakage due to failure of a tubular electric heater.
Why does Samsung give out a code when washing?
Water may leak from the drum for various reasons. Before you begin to solve the problem, you need to establish exactly why it arose.
The le error may be based on several objective reasons:
Incorrect connection of the drain hose to the machine or sewer pipe.- A crack in the drain tube or a broken hose mounting clamp.
- Damage to the seal, which allows emergency water leakage.
- Poor fixation of the drain filter after the last cleaning.
- Blockage of the washing powder dispenser compartments in the tray.
- The appearance of defects in the drum or the body of the washing tank itself.
- Failure of the pressure switch (sensor that monitors the liquid level).
- Broken contacts and connections of the water sensor.
- Abrasion or cracks appear in the sealing collar on the door.
- Malfunction of the electronic control unit of the washing machine.
- Leaks in the water supply (or sewer) pipe leading to or from the machine.
Some of these reasons are not global and can be easily eliminated. These include, for example, incorrect installation of the drain hose.
The list of reasons also includes more serious items that require the intervention of a specialist and financial costs to correct the defect. The further fate of failed household appliances in any case depends on competent diagnostics.
Reasons for the error
There may be several reasons for this failure:
- Insufficient water supply - blockage in the water supply tube, malfunction of the tank filling sensor.
- The presence of leaks, both external and internal. The most common holes are in the drain hose and its connection point, as well as in the rubber pad that separates the pump from the drum. You can check for leaks visually - inspect the area around the machine; a large amount of water near it indicates a leak. Internal damage is more difficult to trace, but it is also possible: check the clamps of the drain hose, the presence of cuts and holes in the rubber lining of the drum.
- The drain hose itself may jump out of the drain hole, especially if the drain is located at a level below the machine, at the bottom of the riser. Pull the hose and listen to see if you can hear water flowing from it. If such a sound is not heard, most likely the water is flowing past it. check the fastenings.
- The most serious damage is a crack in the washing machine body or its drum. Such breakdowns are easy to see visually.
Important! If there are cracks in the outer casing or drum, it is recommended to immediately disconnect the washing machine from the mains and not turn it on until the problem is resolved, as this may lead to electric shock to a person.
What to do?
Further actions to eliminate the le error depend on the identified cause. You can eliminate many of them yourself, without turning to a specialist.
Each cause has its own solution:
If the drain hose is the culprit, adjust its connections. The entry point of the hose into the sewer pipe should be above the machine tank. If necessary, the joint is sealed with a new rubber gasket.- Correct the position of the drain hose. He must make an upper loop between the connections to the machine and the sewer (at least 70 cm from the floor).
- If the cause is the drain filter, then it must be tightened more tightly to stop water flowing through it.
- If water spills out of the dispenser tray, rinse it thoroughly. The outlet channels of all tray compartments clogged with petrified powder must be cleaned.
- If there is a leak at the connections of the pipes that go from the tray to the tank or from the tank to the pump, they are tightened more tightly. You can do this procedure yourself only if you have the skill to work with equipment.
- If the culprit of the error is the water level sensor, then it is necessary to correct its connections and contacts. This manipulation is also only available if you have experience working with electronics and electrical equipment.
If there is no visible leakage and the error does not disappear, then you should try turning off the device completely. A reboot helps resolve the failure in the control module.
Call the master
When independent attempts to resolve the le error do not lead to success, you need to seek help from a washing machine repair specialist. He will conduct a full diagnosis and offer the most optimal solution to the problem.
You can find a professional in workshops specializing in household appliances . Such offices are available in all major localities. You can also order a call from a specialist through online advertisements or advertising posters.
It is best to seek help from officially operating workshops. They not only have all the necessary permits for work, but also issue a warranty card. When calling a specialist through a private advertisement, there is a risk of becoming a victim of fraud.
The total cost of repairing a Samsung machine due to an error le depends on many factors . First of all, this includes the volume and complexity of the work, as well as the cost of components:
replacing a damaged drain hose on a washing machine costs an average of 1,400 rubles;- adjusting the sensor connection by replacing a frayed cable or twisting wires - from 1800 rubles;
- removing a faulty one and installing a new water sensor or replacing a microcircuit – from 2,400 rubles;
- repair or replacement of the rubber door seal on a machine - from 1900 rubles.
How to prevent the problem from occurring?
To protect your washing machine from error le, it is enough to follow the rules for servicing household appliances and promptly notice any problems that arise.
This is necessary already at the stage of installing a new device in the house. Such measures include proper connection and installation of the drain hose, control check of water and sewer pipes.
During operation, it is important to monitor the condition of all rubber seals, drain hose, detergent tray, drain filter and other parts responsible for the occurrence of error le.
It is also important to observe the dosage of detergent . Excess powder, as well as the use of a product not intended for automated washing, can lead to increased foaming and problems with the operation of the unit.
Adviсe
Despite the fact that the Samsung washing machine performs work in an automated mode, after starting the program it must be periodically monitored.
Since the problem coded by the le code is related to the release of water from the tank, unauthorized drainage is often the cause of flooding.
If automatic water filling and draining is repeated several times, the volume of liquid around the machine increases. You can only stop this process manually by pressing the corresponding button or unplugging the power cord.
The second recommendation concerns the quality of connecting nodes and contacts. After cleaning the filter and other elements, it is important to tighten the parts tightly. When reinstalling the drain hose, you should check the degree of sealing of the entrance to the sewer pipe.
If the reasons for the error le are related to the internal structure of the machine (sensor, tank, contacts, control unit), and the level of competence does not allow you to figure it out on your own, then you should not take on the job. It is better to entrust this important task to a master.
You can learn more about error codes for Samsung washing machines here.
Other malfunctions of Samsung washing machines that require specialist intervention
- Aquastop being cut in a Samsung washing machine - hit by a sharp object - repair cost starts from $35;
- The Samsung washing machine displays an error LE or LE1 – damage to the drain pipe by a sharp object – repair cost starts from $20;
- The wash does not start - the water level sensor is faulty - the cost of repair is from 20 dollars;
- The automatic machine gives an error when washing, spinning - malfunction of the display unit - the cost of repair is from 50 dollars;
- The automatic machine displays a leak or self-draining error - erroneous operation of the water leak sensor - repair cost starts from $35;
- Water leakage along the back wall - replace the drain hose - repair cost starts from $20;
- The machine automatically gives an error - a wiring fault - the cost of repair is from 15 dollars.
