Home » Household

How to tighten or replace a belt on a washing machine


Reasons for replacing the drive belt in a Samsung car

The following reasons push washing machine owners to replace parts:

  1. An uncharacteristic noise or rumble is heard during washing.
  2. Upon inspection, the surface of the part is rough (looks like dirt), and when rubbed, it rolls into balls.
  3. You have been using the machine for more than 6 years - this is usually the service life of the part.

If at least one of the above reasons is confirmed, you need to carry out a technical inspection of the machine - you may need to replace the part.

Next, we will look at how to change the belt on a Samsung washing machine.

Important! In the model range of this brand, the back panel cannot be removed, so repairs are somewhat more complicated.

How to replace or put on a belt on a washing machine

Absolutely all causes of malfunction involve tightening or replacing components. The torn part must be replaced. It is better to install a new strap if the old one is worn out and slipping. You can determine the problem by spinning the drum. If the part rotates easily, then the element is not positioned correctly. Before you finally change the unusable belt on your washing machine, you should choose the right one.

Selecting a replacement belt

The part is selected according to the old marking - 4 letters and 1 number. When purchasing you need to take into account:

Read also:  Where does the unpleasant smell from the dishwasher come from and how to remove it?
  • rigidity and elasticity. They are designated by the letters EP, EL, MAEL, E. Elastic products are suitable for modern models, and rigid ones are suitable for outdated ones and require adjustment of the tank to the engine;
  • belt length. The short one may break during operation, and the long one may fly off;
  • profile. The J-marking indicates the wedge spacing is 2.34mm, and the H-profile is 1.6mm. Please note that the H-profile strap is not suitable for an engine with a J-profile;
  • number of wedges. The size is not critical, but a narrow strap with a small number of wedges falls off more often than a wide one with a large number of notches;
  • part code. For outdated Bosch washing machines you will need a 1192 J3 belt, for narrow Samsung machines a 1270 J3 belt is suitable, for medium and wide ones - 1270 J5;
  • material. Rubber belts are durable and have a low elongation coefficient. Polyurethane ones are easier to install, but wear out faster.

Advice!
The number of wedges is indicated next to the profile. In addition to the basic selection parameters, it is important to consider the type of product.

Wedge type

V-belts are used for machines with asynchronous motors. The shape of the product is similar to a truncated triangle or trapezoid. The belt is tough, but durable and elastic. Manufacturers produce products:

  • for foreign cars - section 3L;
  • for domestic washing devices - sections A and Z.

The markings can be read on the outside.

What is the best way to put a V-belt on a working washing machine? Installation begins with the motor pulley and then recesses it into the drum groove. It is required to make a deflection and strengthen it by 5 mm in the center. Otherwise, it will slip and the spin will be weak. For tension, the engine is gradually moved with the fasteners previously loosened.

Poly V-type

The product with a rivulet profile is suitable for SMAs with commutator electric motors. It is made in the form of wedges arranged in a row, which form teeth. The flat belt is flexible, solid, able to withstand loading with a large amount of laundry and smooth rotation. The grooved parts differ in the depth of the chamfers and the number of grooves (3-9). Indicators determine the density and permissible load during operation.

Compared to a wedge product, the part is weaker, so effort must be made when tensioning. To control the strength, the product is rotated along its axis in the center by 360 degrees.

After replacement, you need to check the position of the belt - exactly in the center of the width of the mating part of the engine pulley and drum.

Important! The tension of poly-wedge models is weaker than wedge-shaped ones, so you need to work with gloves.

Replacing a belt in a Samsung machine

To replace the drive belt, proceed as follows:

  1. Remove the back panel by unscrewing the fasteners.
  2. For models that do not have a removable back panel, you must remove the front panel. In this case, work is carried out from above.

To remove the front panel:

  • Unscrew the lid.
  • Take out the powder dispenser (it has a small button inside for easy removal).
  • Remove the control panel and place it on top out of the way.
  • Unscrew the bottom panel.
  • Unscrew all the screws that secure the front cover and pull it towards you.
  1. Arm yourself with a slotted screwdriver - using it carefully, lightly hook the edge of the belt.
  2. Remove the belt from the grooves on the pulley by sliding it to the side.
  3. Rotate the pulley while holding the strap with your hand. After this, the belt should easily come off the pulley and you can safely remove it from the housing.

Important! If there is a “beard” and it is wrapped around the engine, be sure to untangle everything and remove it.

How can you tell when it's time to change the belt in your washing machine?

The first reason: your machine has stopped turning the drum, although you can hear that the engine is running. The problem is most likely that the belt has broken or fallen off.

The second reason is that when the load is light, the drum jerks in place and the engine cannot turn it. Reason: the belt became thin, lost its rigidity and stretched.

The third reason is that the drum rotates when the load is light and does not rotate when the load is fully loaded. The reason is also in the belt.

Read also:  Siemens dishwasher error e15 how to reset?

The fourth reason is that when the drum rotates, extraneous sounds arise, as if something is rustling or touching inside. The reason is that the belt has delaminated, and its fragments hit the walls of the case and parts of the washing machine. This situation is the most unpleasant and can lead to serious consequences. Fragments of the belt can snag the wires and break them, as well as wrap around the engine and cause its failure.

These are the main reasons why belt replacement is vital!

Installation work

Important! Buy a part with 5 streams (Megaden production is suitable). Buyers respond positively to it, praising the quality and especially the silicone inserts that extend service life.

Don't know how to tighten the belt in a Samsung washing machine? All the hardest parts are already behind you - all you have left are the final chords. Just a few steps separate you from using an updated machine:

  • Place the new part on the pulley so that the grooves line up as specified by the manufacturer.
  • If you work from above the CM, then help yourself with a strong thread or a piece of used belt. Tie the belt to an improvised “fishing rod” and lower it into the body. Hold it with one hand and put it on the engine with the other.
  • Now stretch and place the part on the side grooves on the pulley.
  • Continuing to create tension, rotate the pulley to the right and everything will fall into place.

If you have a Samsung S1021, S803J or S803J model, now you know how to remove and install the drive belt. For other SM models, the replacement process is similar.

We hope the installation goes smoothly and successfully. Good luck with your renovation!

How to change the belt on a Samsung washing machine ✅: replacement, tension, put on, install

The drive belt is an important part of the washer that rotates the drum. If it fails or falls off, the device stops performing its tasks. To restore functionality, you need to change the belt on a Samsung, LG washing machine or a model from another manufacturer.

When replacement is required

Determining when to replace the belt in a Samsung washing machine is easy. The first sign of a malfunction is the activation of the self-diagnosis sensor.

Advanced devices are equipped with special systems that record all breakdowns and send information to the user in encrypted form.

If the washer has a screen, an error code will appear on it.

Then it needs to be deciphered using the table for the corresponding model.

There are other problems that indicate loss of tension:

  1. The device is running, there is noise from the motor, but the drum refuses to rotate.
  2. The engine makes a running sound but keeps cutting off and starting again. Similar phenomena occur at regular intervals.
  3. The wash cycle starts, but the electronic system displays errors and does not respond to user commands.

If at least one sign appears, it is necessary to stop the wash and evaluate the condition of the drive.
You should also prepare tools for repairs, disconnect the device from the power supply and study the sequence of further actions. What brand of equipment do you use at home? Poll Options are limited because JavaScript is disabled in your browser.

Read also:  A bra wire got into the washing machine - what to do and how to get it out

Total votes: 5230

Voted: 3014

22.01.2020

×

You or from your IP have already voted.

Which belt to choose

When choosing a new element for the drive, you should familiarize yourself with the markings of the old model and find a suitable analogue. But if there is no way to clarify the name, you will have to select a part from the list of available options.

Removing old

Before you put a new part on the pulley, you need to determine where it is located. In case of a single problem, it is enough to reinstall the part and make sure the device is working.

If the malfunction occurs regularly, you will need to install a belt on the Samsung washing machine. The algorithm of actions is as follows:

  1. The machine must be disconnected from the power and water supply, and then remove the drain and fluid intake hose.
  2. The device is moved to the middle of the room to make it more convenient to carry out repair work.
  3. The belt is located behind the rear wall between the motor and drum pulleys. To remove it, you need to unscrew the screws that hold the cover in place.
  4. If the part lies at the bottom of the case and there are no signs of damage, it needs to be put back in place.
  5. If defects are detected, the belt must be removed from the case and the markings found on it. This can be a set of letters or numbers. It is important to find the first 4 digits that indicate the length of the part in mm. Next, you need to measure the belt and make sure that the actual length matches the declared one.

How to tension a new belt

To tighten the new belt, you need to tie a strong cord or secure a wire to the pass. Next, the part needs to be lowered through the top and secured behind the engine pulley. Gaining access to this part of the machine is easy: just tilt it so that the tank moves. By working with an assistant, you can simplify this task, because... another person will be able to hold the fastener and evaluate the correct tension.

The next step is to pull up and put the part on the drum pulley. The pass must be placed in the central part of the lane and firmly recorded.

Finally, all that remains is to remove the auxiliary cord and start the washing machine to check its functionality. To protect the device from damage or the drive belt falling off, it is necessary to place it on a flat surface and avoid overloading the drum. Replacing the belt in a Samsung washing machine yourself is not a difficult task. The main thing is to follow the step-by-step guide and adhere to the installation rules.

Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
You may also be interested
How to change the belt on a washing machine
Changing the belt on an Ariston washing machine
Step-by-step guide on how to change the belt on a Samsung washing machine
How to check and replace shock absorbers on a washing machine
Washing machine belt
What to do if the belt falls off the washing machine drum
How to replace the drum bearing of an Indesit washing machine with your own hands
close the necessary contacts
How to replace a washing machine lock (UBL)
Washing machine motor
Replacing brushes on a washing machine in Moscow
Error E18 in a Siemens washing machine
Replacing a bearing on an Ariston washing machine
tank without counterweight
Replacing bearings in a Samsung Diamond washing machine
badges on SM Kandy
What do the icons on the washing machine mean?
Shuttle type in a washing machine: which is better?
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]